Podolsk,
14 Lobacheva st.
To contact page
RU EN
Tue-Fri 11:00-20:00
Sat-Sun 11:00-17:00
Mon - Closed
Airframe Pro TopShelf
Motorcycle helmet
Airframe Pro TopShelf
Airframe Pro TopShelf
Airframe Pro TopShelf
Airframe Pro TopShelf
Airframe Pro TopShelf
Airframe Pro TopShelf

See how to choose the right size in the “Size” tab below.

RUB 37,000 RUB 30,000

Steel skates and a fiberglass mask — the best of old-school hockey. Built on a lightweight FRP fiberglass shell, the Topshelf helmet includes Fog-Free Clear and Dark Smoke Optics visors. The adjustable 5-piece Hydradry comfort liner lets you fine-tune the fit. The extensive AFP ventilation system makes it one of the most ventilated helmets in the industry.

WORLD STANDARD

  • Meets the DOT FMVSS 218 (USA), ECE 22.06 (Europe) and PSC (Japan) helmet safety standards.

VISOR

  • Includes a standard Clear Fog-Free Icon Optics™ visor and an additional dark Icon Tracshield™ visor.

EXTERIOR

  • Reduced drag and weight are achieved through the rear cutout traditional for ICON helmets, which also improves ergonomics where the helmet meets a motorcycle jacket or race suit.

LINER

  • Five-piece modular liner with a moisture-wicking Hydradry™ finish.

VENTILATION

  • Nine intake and five exhaust vents provide excellent ventilation.
  • The forehead vents are angled to provide linear airflow at speed, and deep channels in the EPS liner improve airflow.

SHELL

  • Handmade composite shell, high-quality fiberglass and precise manufacturing technology.

Let’s be honest — motorcycle helmets look great, and you’d like to keep yours looking like new for as long as possible. Over many years of practice we have worked out several effective ways to do this, and we are happy to share them.

CLEANING THE HELMET

We strongly do not recommend using solvents, carburetor cleaner, brake fluid or any other substances in the cans, tins and bottles lying around your garage, including unlabeled ones, to clean your helmet. Chemicals and strong solvents can seriously damage the materials the helmet is made of — please don’t do that to your helmet!

WASHING THE LINER

  • Remove the inner comfort liner as described in the “Removing the comfort liner” section of the ICON helmet manuals.
  • Soak the liner in a mild solution of baby shampoo and wash it gently.
  • Rinse several times in clean water until all traces of soap are gone.
  • Let the water drain and air-dry the liner, then reinstall it in the helmet.

* Never wash or dry the liner in a washing machine or dryer.

CLEANING THE OUTER SURFACE (GLOSS HELMETS)

  • Cover the helmet with a towel soaked in hot water and leave it for at least 5 minutes to soften dried-on bugs (don’t skip this step!).
  • Take a fresh towel soaked in a dishwashing liquid solution and remove dirt from the helmet surface.
  • Use a third, dry towel to wipe the helmet and remove water marks.

CLEANING THE OUTER SURFACE (RUBATONE MATTE HELMETS)

  • Cover the helmet with a towel soaked in hot water and leave it for at least 5 minutes to soften dried-on bugs (don’t skip this step!).
  • Remove bugs and dirt with light blotting motions. Use the soft inner side of the included helmet bag or a clean microfiber cloth.

POLISHING THE OUTER SURFACE

  • For helmets with a gloss finish, use an aerosol car wax (sold in any auto store).
  • As for matte parts, we sincerely hope you are not planning to polish a matte surface.

STORING THE HELMET

Protecting your helmet during long-term storage is definitely a good idea. Keep the helmet in the special bag included. Store it in a safe, dry place out of direct sunlight.

CLEANING THE VISOR

The visor surface must be cleaned very carefully to avoid scratches. Place a clean, warm, damp, soft cloth over the outside of the visor for at least 5 minutes to soften dried bugs and dirt (don’t skip this step!). Then gently clean the visor with a clean soft cloth, warm water and mild soap. After that, wipe the visor with a clean soft cloth dampened with clean water to remove soap residue. Dry the visor by gently wiping it with a clean soft cloth.

Never use solvents, window or glass cleaners, or any other chemical cleaners to clean the visor.
Do not apply decals, tape or stickers to the visor.

If your visor has an anti-scratch or anti-fog coating, keep in mind that household cleaners (such as glass cleaners, all-purpose sprays, furniture polish) can leave unwanted marks and in some cases damage the visor itself.

Do not use any cleaners or detergents on the inside of the visor. Using anything other than a clean soft or microfiber cloth and water to gently wipe the inside of the visor can damage or reduce the effectiveness of the anti-fog coating.

Protect the visor when it is not fitted to the helmet. Store the visor in a dry, safe place, away from direct sunlight and extremely high or low temperatures. Make sure the visor cannot be scratched, damaged by impact or otherwise deformed, is not under heavy objects and is not stored near fuel or solvents. We recommend storing the visor in a soft microfiber bag or pouch.

If your helmet has an internal drop-down visor, be sure to follow the same instructions, as they also apply to the internal drop-down visor.

GOOD ADVICE

Although a helmet is hard and has a very strong and reliable construction, it requires careful handling. Dropping a helmet on asphalt or another hard surface can significantly impair its functionality. The user should be aware that an impact may cause damage that is invisible to the eye.

GOOD ADVICE FROM ICON

The riding gear manufacturer ICON Motosports warns: when taking part in activities that require a helmet on your head, it is strongly recommended to avoid hitting your head on anything whatsoever. If you suspect reduced helmet functionality, or after ANY impact during use, replace the helmet. We guarantee it will cost less.

  • DO NOT PULL THE HELMET OFF BY GRABBING THE VISOR OR SPOILER LIKE A HANDLE. THESE PARTS ARE DESIGNED TO BREAK AWAY IN A CRASH.
  • BEFORE REMOVING THE VISOR SIDE PLATE, REFRESH YOUR KNOWLEDGE BY REREADING THE “VISOR REMOVAL/INSTALLATION” SECTION OF THE HELMET MANUALS.
  • DO NOT LEAVE THE HELMET ON THE FUEL TANK. GASOLINE FUMES CAN DAMAGE THE HELMET LINER THAT DISSIPATES IMPACT ENERGY IN A CRASH.

No motorcycle helmet in the world can protect against ALL possible impacts. For your safety, you need to choose a helmet that fits correctly. For maximum head protection, the helmet must fit snugly and follow the shape of your skull as closely as possible. To work properly, the helmet must be securely fastened under the chin.

MEASURING YOUR HEAD

Wrap a flexible measuring tape around your head at its widest point above the eyebrows and ears.

Using this measurement, find your size in the size charts below according to the helmet brand and model:

ICON AIRFLITE / DOMAIN / THRESHOLD

BILTWELL LANE SPLITTER / GRINGO S SV

THOR FLEET / SECTOR 2

Shell 2XS XS S M L XL 2XL 3XL
Circumference cm 51–52 53–54 55–56 57–58 59–60 61–62 63–64 65–66

 

ICON ULTRAFLITE / AIRFRAME PRO

THOR REFLEX

Shell XS S M L XL 2XL 3XL
Circumference cm 54–55 55–56 57–58 58–59 60–61 62–63 64–65

 

ICON AIRFORM

Shell XS S M L XL 2XL 3XL
Circumference cm 53–54 55–56 57–58 58–59 60–61 62–63 64–65

 

HEAD SHAPE

Skull shape in the horizontal plane is just as important as circumference. To determine your head shape, put on a balaclava (it will flatten your hair) and take a photo of your head from above, or ask someone to assess it. Round head — width and length are almost the same, it fits into a circle. Intermediate oval head — slightly longer than it is wide, the most common skull shape, it fits into a regular oval. Long oval — noticeably longer than it is wide, it fits into a narrow oval.

Different helmet models are made for different skull shapes — keep this in mind when choosing a helmet:

  • ICON helmets: Airflite, Airform are made for an intermediate oval head. The Airform feels slightly wider than the Airflite. The Airflite also fits a long oval head well.
  • ICON helmets: Ultraflite are made for an intermediate oval head, but they also fit a long oval head well, as well as a head shaped between round and oval, but not a round one. The Ultraflite feels slightly wider than the Airflite. Overall, the Ultraflite is a more adaptable helmet and fits a wider variety of intermediate oval and long oval heads than the Airflite.
  • ICON helmets: Threshold are made for an intermediate oval head. They fit similarly to the Ultraflite, meaning they are more adaptable and suit a wider variety of heads that deviate from the intermediate oval toward both round and long oval.
  • ICON helmets: Domain — for a round head (Round Oval), but it also fits an intermediate oval head well.
  • ICON helmets: Airframe Pro — for intermediate oval and long oval heads.
  • BILTWELL helmets: Gringo SV, Gringo S and Gringo — for round (Round Oval) and intermediate oval heads.
  • BILTWELL helmets: Lane Splitter — for round (Round Oval) and intermediate oval heads.
  • THOR helmets: FLEET fit round (Round Oval) and intermediate oval heads very well.
  • THOR helmets: REFLEX are made for an intermediate oval head, but they also fit a long oval head well.
Head shapes: round oval, intermediate oval, long oval

If you can’t determine your head shape (this sometimes happens), it is most likely an intermediate oval, because a round head shape (equal length and width) is the most obvious.

If your head shape doesn’t match the helmet shape, you need to go one or two sizes up, depending on how big the difference in skull oval is. In that case the liner will fit your skull unevenly and not over its whole area, which has a negative effect on impact energy absorption as well as on the helmet’s noise insulation.

NOTE: The helmet’s inner pads compress with use — keep this in mind when trying it on. The helmet should fit snugly and should not press painfully on your skull. The pressure on your cheeks can be quite strong, and they may be squeezed. The cheek pads are the thickest and compress the most.

We don’t believe you need to wear a helmet for a while to get used to it. A helmet chosen correctly by size and shape fits comfortably and snugly right away — proven by hundreds of customers! The only thing that may be uncomfortable is a tight entry when taking the helmet off and putting it on. Over time the pads at the entry will soften, and the helmet will be much easier to put on and take off. Focus on how your head feels inside the helmet!

This manual contains instructions on choosing a suitable motorcycle helmet, and on wearing, caring for and replacing it in good time. Failure to follow the instructions given here may increase the risk of serious injury or death in a crash.

For maximum protection, always follow these instructions. Always wear a helmet when riding a motorcycle. Handle the helmet carefully to avoid accidental damage. Follow safety rules while riding. Don’t take risks just because you are wearing a helmet.

RELEASE OF THE MANUFACTURER FROM LIABILITY BY THE PRODUCT OWNER

No personal protective equipment can protect against all types of injuries in a crash or fall from a motorcycle. No riding gear can provide complete protection against impacts or abrasion in a crash or fall from a motorcycle. Motorcycling is inherently dangerous, and using this helmet cannot prevent injury or death. Even at low speed, a crash can result in serious injury or death. By using this helmet, the user assumes all risks associated with this activity that may result in injury or death. The user hereby waives all claims and lawsuits against Icon® Motosports, Lemans Corporation and J-TECH Corp in the event of death or injury resulting from the use of Icon Motosports products.

ANGLE OF ATTACK

The modern riding position with high footpegs and low clip-ons has a significant effect on how the rider interacts with a modern hyperbike. In an even more “tucked” position, the rider has to tilt their head back at a steep angle to maintain good visibility and stability. With these aspects in mind, Icon® created the AIRFRAME PRO helmet. By focusing primarily on design and shape, we reduced weight and achieved a closer fit, creating a helmet with a natural neckline to avoid catching on a jacket or suit.

Aggressive geometry has made it possible to widen the field of view and improve aerodynamics in a fully “tucked” position. The much smaller profile of the shell, made of aerospace-grade carbon fiber or fiberglass composite, carries the ECE certification recognized by athletes. Precise assembly techniques help reduce weight, allowing Icon® to create unrivaled lightweight and superbly equipped helmets. The inner liner, which traditionally consisted of three parts, has been improved and now consists of five, allowing a much more comfortable and snug fit on any head shape. Crown, side, front and rear pads allow the helmet to be adapted to 27 different shapes within one shell, twice as many as helmets competing with the AIRFRAME PRO. Both the inner and outer construction of the Icon® AIRFRAME PRO helmet are optimized for the angle of attack.

REPLACEMENT TIPS

The advice to replace your helmet every five years is based on the consensus of most helmet manufacturers. Glues, resins and other materials used in helmet production can affect the liner material over time. Skin oils, sweat and cosmetics, as well as normal wear of the materials, also lead to deterioration of the helmet liner.

In addition, petroleum-based products in cleaners, paints, fuel and other commonly used substances can damage the materials used in helmet production, potentially impairing their performance. Experience shows that helmet quality standards are revised every five years. Combined with statistics on improvements in materials, design and manufacturing methods, this leads to the conclusion that it is in the owner’s interest to replace their helmet at least every five years.

SAFE USE WARNING

Motorcycling is a dangerous activity. No helmet can protect against all possible injuries. Always wear a helmet, eye protection, protective clothing, gloves and boots when riding. However, there is no guarantee that wearing the helmet described in this manual will prevent serious or fatal injury. Take every possible measure to avoid any risk. This helmet is not intended for use as a fire-resistant product, as it does not contain fire-resistant materials. Make sure the Icon® products you buy fit you correctly. A loose fit may reduce your ability to control the motorcycle.

CONSTRUCTION

The ICON® AIRFRAME PRO helmet is designed to the ICON WORLD STANDARD, which meets or exceeds the requirements of the DOT FMVSS 218 (USA), ECE 22.05 (EUROPE), SAI AS1698:2006 (AUSTRALIA) and PSC (JAPAN) helmet safety standards. These head protection standards are officially recognized in more than 50 countries. Before repairing or replacing parts of the AIRFRAME PRO helmet, review the diagram below to familiarize yourself with the specific names and terms used to describe the helmet.

  1. MAIN VENT
  2. FOREHEAD VENT
  3. EYEPORT GASKET
  4. VISOR
  5. VISOR LOCKING SYSTEM
  6. SIDE PLATES
  7. BREATH DEFLECTOR
  8. PROLOCK™
  9. MOUTH VENT
  10. SIDE VENT
  11. DOUBLE D-RING
  12. OUTER SHELL
  13. DUAL-DENSITY EPS LINER
  14. REAR EXHAUST VENT
  15. IMPACT-ABSORBING LINER
  16. COMFORT LINER
  17. BASE GASKET
  18. CHIN STRAP

DO NOT MODIFY THE HELMET. To keep this helmet effective, its construction and components must not be altered. Paints and adhesives can damage the helmet without the user noticing and reduce its effectiveness.

SHELL AND EPS LINER CONSTRUCTION

SHELL

Thanks to industry-leading pneumatic molding processes, the composite materials used to make the AIRFRAME PRO, such as fiberglass, Spectra® and carbon fiber, form a special mesh structure system that provides superb strength along with centered mass and minimal helmet weight.

  1. FIBERGLASS
  2. SPECTRA®
  3. CARBON FIBER
  4. GRAPHICS AND FINISH

EPS LINER

The dual-density EPS liner of the AIRFRAME PRO helmet actually consists of two expanded polystyrene layers that provide maximum impact protection and dampen impact force. In addition, both layers have many air channels to distribute air from the external ventilation system.

  1. AIR CHANNELS
  2. COMPOSITE SHELL
  3. SOFT OUTER LAYER
  4. RIGID INNER LAYER

PROPER FIT

To ensure a proper fit, follow these instructions:

  1. Put the helmet on so that it sits low on your forehead. If you cannot see the edge of the eyeport at the top of your field of vision, the helmet is probably not being worn correctly. Adjust the retention system so that when fastened it holds the helmet firmly in place. The size chart is for information only. Always try on a helmet before buying and follow the instructions in this manual to ensure a proper fit.
  2. With the chin strap fastened as tightly as possible, hold the helmet with both hands. Without moving your head, try to move the helmet up and down and from side to side. When you try to move the helmet, you should feel the skin on your face and scalp pull. If the helmet moves too easily on your head, it is too big for you. Try a smaller size.
  3. With the chin strap fastened, place your palms flat on the back of the helmet and try to roll it off your head forward. Then place your palms on the front of the helmet and try to roll it off backward. If the helmet comes off in either direction, it is either too big or the chin strap is not tight enough. Make sure you have good visibility for operating the motorcycle safely.

CHIN STRAP

For the helmet to work properly, the chin strap must always be securely fastened when worn. With the chin strap fastened, the helmet must not come off when pulled from the center of the back. Periodically check the chin strap to make sure vibration has not loosened it. To check, simply pull on it a little.

To securely fasten the D-ring retention system, thread the end of the chin strap through the D-rings exactly as shown in the figure below. Fasten the snap on the chin strap to secure the loose end of the strap once it is securely fastened. The only function of the snap at the end of the chin strap is to keep it from flapping in the airflow. It is not part of the retention system. It should be used separately, without threading through the D-rings, as shown below.

To unfasten the D-ring retention system, release the loose end of the chin strap from the snap. Then pull the red tab at the end of the lower D-ring to loosen the chin strap. After that, pull the end of the chin strap back through the D-rings to release it completely.

Make sure the chin strap is fastened according to the instructions above. Mishandling the strap may result in serious injury or death.

Safe use warning: Do not rely on the chin strap snap alone. It only serves to keep the loose end of the strap out of the way while riding. Fasten the retention system only as shown in the image.

AIRFRAME PRO VISOR

The Airframe Pro is fitted with an Icon Optics™ visor that provides an unrivaled clear and unobstructed view. All Icon Optics™ visors feature the exclusive Rapid Release™ system, making visor removal and replacement easier than comparable solutions on the market. Icon® visors are available in different tints and styles, each ideal for any situation on the road.

The Icon Optics™ visor supplied with this helmet meets VESC-8 standards. Visors marked “for daytime use only” must not be used at night or in poor visibility. Make sure the visor is always in excellent condition.

The Icon TracShield™ visor for AIRFRAME PRO helmets is a good choice for users who prefer tear-off protective film. The TracShield™ visor is compatible with the Rapid Release™ system and fits AIRFRAME PRO and Airmada helmets. The visor is available in four tints: dark, clear, yellow and silver RST. Tear-off film is sold separately.

VISOR REMOVAL AND REPLACEMENT

  1. To remove the visor, open it fully.
  2. Move both locking levers to the “open” position toward the back of the helmet and remove the visor from the toothed base plates.
  3. Once removed, hold the visor in one hand and with the other detach the side plates from the edge of the visor (by the front of the side plate).
  4. Pull each side plate toward you until it separates from the visor.
  5. To replace the visor, line up the tabs on the visor with the notches on the base plates and slide it into place until it clicks.
  6. To replace the side plates, line up the tabs on the side plate with the notches on the visor and snap it on. Repeat for each side plate.
  7. Check that the visor opens and closes before riding.

INTERIOR PARTS

The Airframe Pro helmet has a fully replaceable set of interior parts covered with Icon®’s exclusive moisture-wicking HydraDry™ material. Helmet size is determined by three factors: the size of the outer shell, the thickness of the inner EPS liner and the thickness of the interior components. You can achieve a more comfortable fit by replacing the existing cheek pads with thinner ones (for more room) or thicker ones (for less room). To order replacement parts, contact your local dealer or visit www.rideicon.com.

REMOVING THE COMFORT LINER

To remove the interior parts for cleaning or replacement:

  1. Detach each cheek pad from the helmet by pushing it inward and releasing it from the retention system.
  2. Turn the helmet over and pull out the cheek pads. Note how the cheek pad plate fits between the helmet shell and the EPS liner; this will be useful for reassembly.
  3. Remove the comfort liner by detaching it from the two-snap system at the back of the helmet. Then remove the liner mounting assembly, noting how it fits between the shell and the EPS liner. Remove the side parts of the liner by pushing them inward and releasing them from the retention system.

VENTILATION SYSTEM

Ventilation is the main feature of the AIRFRAME PRO helmet. The helmet has nine intake and five exhaust vents. The forehead vents are angled to provide direct ventilation at speed. The deep-channeled EPS liner improves ventilation by directing air more efficiently. The chin vent is designed for breathing in a fully tucked position, providing airflow at the corresponding angle of attack. The ventilation system is completed by low-pressure exhaust vents.

The AIRFRAME PRO helmet has four simple switches that let you control airflow into the helmet. To open the forehead vents (1a, 1b), slide the switches in the slots up. To close them, simply slide them down. Similarly, to open the side vents (2a, 2b), slide the switches in the slots back, and to close them, forward. To open the chin/visor vent (3a, 3b), press and slide the switch in the slots. To close it, press and slide the switch back in the slot area.

RECOMMENDATIONS

ONE-IMPACT RULE — AFTER ANY SEVERE IMPACT, THE HELMET MUST BE REPLACED.

Helmets are designed to protect against one impact only. The helmet is designed so that the head is protected in an impact through damage to the shell and EPS liner. In any hard impact on the helmet, the area of the liner that takes the impact absorbs and dissipates the force, which compresses it and damages the liner. The damage may not be visible. Even if no VISIBLE damage is found on the shell, the helmet will be unfit for use after one impact. After an impact, replace the helmet with a new one and dispose of the old one, even if it appears undamaged.

HELMET WEAR AND DISPOSAL

A helmet has a limited service life and must be replaced when typical signs of wear appear, such as changes in shape, cracks, corrosion, abrasion or other signs of material wear that could lead to helmet damage.

CAUTION: After buying a new helmet, dispose of the old one so that it is not reused. Do not sell or give away your old helmet, even if it is undamaged. Over time, the protective layer in a helmet takes the shape of the rider’s head. Such a helmet cannot provide another rider with a comparable level of protection.

PROPER HELMET USE

SAFE USE WARNING: To reduce the risk of serious injury or death and prevent damage to the helmet, follow these instructions. Do not adjust helmet parts while riding; do it only when you have stopped. Do not drop the helmet: this can damage the shell or the protective foam. The damage may not be visible. The helmet is designed for ONE impact only. For more information, see the “REPLACEMENT TIPS” section. Do not wear other headwear under the helmet, as this may reduce its effectiveness. Do not hang or attach the helmet on any fixtures, including mirrors, handlebars or the passenger grab handle: this can damage the protective foam or liner of the helmet. Do not spray insect repellent near the helmet: it can damage the visor, shell, protective foam and other parts of the helmet. Do not expose the helmet to gasoline or gasoline fumes: they can damage the visor, shell, protective foam and other parts of the helmet.

HELMET INSPECTION

SAFE USE WARNING: To reduce the risk of serious injury or death, always follow the helmet operating rules.

  • Inspect the visor and visor mount — tighten the mounting screws if necessary. Do not overtighten the screws. Overtightening can break the plastic base plate screws or strip the threads of the aluminum screws.
  • Inspect the helmet for damage. If you notice damage or cracks on the helmet, stop using it immediately. For more information, see the “REPLACEMENT TIPS” section. Damage to a helmet resulting from a drop may not be visible.
  • Inspect the helmet for worn or damaged parts. Plastic parts wear out over time. If you find damaged or worn parts, replace them or buy a new helmet. A full list of replacement parts and accessories for the helmet, including liners, cheek pads, side plates, breath deflectors and much more, is available at WWW.RIDEICON.COM
1/1

Airframe Pro Helmet - Angled For Attack

114 505
Recommend
Magazine Icon Motosports Brand Protection Magazine ZX636 03-04 Stunt Bike Build Stunt Show with Girls Baldini Stunt Show