Podolsk,
14 Lobacheva st.
To contact page
RU EN
Tue-Fri 11:00-20:00
Sat-Sun 11:00-17:00
Mon - Closed
Airform Kryola Kreep MIPS
MIPS motorcycle helmet
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS
Airform Kryola Kreep MIPS

See how to choose the right helmet size in the “Size” tab below.

RUB 26,600 RUB 23,900

This helmet is dedicated to everyone who refuses to color inside the lines. The Airform MIPS Kryola Kreep™ helmet is a real find for artists who dream of graffiti. This ECE 22.06 certified helmet is fitted with the revolutionary MIPS Brain Protection System (BPS), so you can head confidently to your canvas of choice, whether it is a highway overpass or a sheet of drawing paper.  The RST Fog-Free Optics™ anti-fog visor and DropShield™ internal tinted goggles let you see your artwork clearly.

WORLD STANDARD

  • Meets the DOT FMVSS 218 (USA), ECE 22.06 (Europe) and PSC (Japan) helmet safety requirements. Helmets are not supplied with PSC certification stickers unless purchased from an authorized dealer in that country.

VISORS

  • Comes with clear and RST purple quick-change Fog-Free Icon Optics™ visors with the Prolock™ locking system. Includes DropShield™ internal tinted goggles.

LINER

  • Hydradry™ liner with moisture wicking.

SHELL

  • Injection-molded polycarbonate shell for strength and durability.
  • Strict and race-inspired, the Airform is built for speed.
  • Thanks to the well-designed neck opening, the Airform is easy to put on and take off.

Let’s be honest — motorcycle helmets look great, and you’d like to keep yours looking like new for as long as possible. Over many years of practice we have worked out several effective ways to do this, and we are happy to share them.

CLEANING THE HELMET

We strongly do not recommend using solvents, carburetor cleaner, brake fluid or any other substances in the cans, tins and bottles lying around your garage, including unlabeled ones, to clean your helmet. Chemicals and strong solvents can seriously damage the materials the helmet is made of — please don’t do that to your helmet!

WASHING THE LINER

  • Remove the inner comfort liner as described in the “Removing the comfort liner” section of the ICON helmet manuals.
  • Soak the liner in a mild solution of baby shampoo and wash it gently.
  • Rinse several times in clean water until all traces of soap are gone.
  • Let the water drain and air-dry the liner, then reinstall it in the helmet.

* Never wash or dry the liner in a washing machine or dryer.

CLEANING THE OUTER SURFACE (GLOSS HELMETS)

  • Cover the helmet with a towel soaked in hot water and leave it for at least 5 minutes to soften dried-on bugs (don’t skip this step!).
  • Take a fresh towel soaked in a dishwashing liquid solution and remove dirt from the helmet surface.
  • Use a third, dry towel to wipe the helmet and remove water marks.

CLEANING THE OUTER SURFACE (RUBATONE MATTE HELMETS)

  • Cover the helmet with a towel soaked in hot water and leave it for at least 5 minutes to soften dried-on bugs (don’t skip this step!).
  • Remove bugs and dirt with light blotting motions. Use the soft inner side of the included helmet bag or a clean microfiber cloth.

POLISHING THE OUTER SURFACE

  • For helmets with a gloss finish, use an aerosol car wax (sold in any auto store).
  • As for matte parts, we sincerely hope you are not planning to polish a matte surface.

STORING THE HELMET

Protecting your helmet during long-term storage is definitely a good idea. Keep the helmet in the special bag included. Store it in a safe, dry place out of direct sunlight.

CLEANING THE VISOR

The visor surface must be cleaned very carefully to avoid scratches. Place a clean, warm, damp, soft cloth over the outside of the visor for at least 5 minutes to soften dried bugs and dirt (don’t skip this step!). Then gently clean the visor with a clean soft cloth, warm water and mild soap. After that, wipe the visor with a clean soft cloth dampened with clean water to remove soap residue. Dry the visor by gently wiping it with a clean soft cloth.

Never use solvents, window or glass cleaners, or any other chemical cleaners to clean the visor.
Do not apply decals, tape or stickers to the visor.

If your visor has an anti-scratch or anti-fog coating, keep in mind that household cleaners (such as glass cleaners, all-purpose sprays, furniture polish) can leave unwanted marks and in some cases damage the visor itself.

Do not use any cleaners or detergents on the inside of the visor. Using anything other than a clean soft or microfiber cloth and water to gently wipe the inside of the visor can damage or reduce the effectiveness of the anti-fog coating.

Protect the visor when it is not fitted to the helmet. Store the visor in a dry, safe place, away from direct sunlight and extremely high or low temperatures. Make sure the visor cannot be scratched, damaged by impact or otherwise deformed, is not under heavy objects and is not stored near fuel or solvents. We recommend storing the visor in a soft microfiber bag or pouch.

If your helmet has an internal drop-down visor, be sure to follow the same instructions, as they also apply to the internal drop-down visor.

GOOD ADVICE

Although a helmet is hard and has a very strong and reliable construction, it requires careful handling. Dropping a helmet on asphalt or another hard surface can significantly impair its functionality. The user should be aware that an impact may cause damage that is invisible to the eye.

GOOD ADVICE FROM ICON

The riding gear manufacturer ICON Motosports warns: when taking part in activities that require a helmet on your head, it is strongly recommended to avoid hitting your head on anything whatsoever. If you suspect reduced helmet functionality, or after ANY impact during use, replace the helmet. We guarantee it will cost less.

  • DO NOT PULL THE HELMET OFF BY GRABBING THE VISOR OR SPOILER LIKE A HANDLE. THESE PARTS ARE DESIGNED TO BREAK AWAY IN A CRASH.
  • BEFORE REMOVING THE VISOR SIDE PLATE, REFRESH YOUR KNOWLEDGE BY REREADING THE “VISOR REMOVAL/INSTALLATION” SECTION OF THE HELMET MANUALS.
  • DO NOT LEAVE THE HELMET ON THE FUEL TANK. GASOLINE FUMES CAN DAMAGE THE HELMET LINER THAT DISSIPATES IMPACT ENERGY IN A CRASH.

No motorcycle helmet in the world can protect against ALL possible impacts. For your safety, you need to choose a helmet that fits correctly. For maximum head protection, the helmet must fit snugly and follow the shape of your skull as closely as possible. To work properly, the helmet must be securely fastened under the chin.

MEASURING YOUR HEAD

Wrap a flexible measuring tape around your head at its widest point above the eyebrows and ears.

Using this measurement, find your size in the size charts below according to the helmet brand and model:

ICON AIRFLITE / DOMAIN / THRESHOLD

BILTWELL LANE SPLITTER / GRINGO S SV

THOR FLEET / SECTOR 2

Shell 2XS XS S M L XL 2XL 3XL
Circumference cm 51–52 53–54 55–56 57–58 59–60 61–62 63–64 65–66

 

ICON ULTRAFLITE / AIRFRAME PRO

THOR REFLEX

Shell XS S M L XL 2XL 3XL
Circumference cm 54–55 55–56 57–58 58–59 60–61 62–63 64–65

 

ICON AIRFORM

Shell XS S M L XL 2XL 3XL
Circumference cm 53–54 55–56 57–58 58–59 60–61 62–63 64–65

 

HEAD SHAPE

Skull shape in the horizontal plane is just as important as circumference. To determine your head shape, put on a balaclava (it will flatten your hair) and take a photo of your head from above, or ask someone to assess it. Round head — width and length are almost the same, it fits into a circle. Intermediate oval head — slightly longer than it is wide, the most common skull shape, it fits into a regular oval. Long oval — noticeably longer than it is wide, it fits into a narrow oval.

Different helmet models are made for different skull shapes — keep this in mind when choosing a helmet:

  • ICON helmets: Airflite, Airform are made for an intermediate oval head. The Airform feels slightly wider than the Airflite. The Airflite also fits a long oval head well.
  • ICON helmets: Ultraflite are made for an intermediate oval head, but they also fit a long oval head well, as well as a head shaped between round and oval, but not a round one. The Ultraflite feels slightly wider than the Airflite. Overall, the Ultraflite is a more adaptable helmet and fits a wider variety of intermediate oval and long oval heads than the Airflite.
  • ICON helmets: Threshold are made for an intermediate oval head. They fit similarly to the Ultraflite, meaning they are more adaptable and suit a wider variety of heads that deviate from the intermediate oval toward both round and long oval.
  • ICON helmets: Domain — for a round head (Round Oval), but it also fits an intermediate oval head well.
  • ICON helmets: Airframe Pro — for intermediate oval and long oval heads.
  • BILTWELL helmets: Gringo SV, Gringo S and Gringo — for round (Round Oval) and intermediate oval heads.
  • BILTWELL helmets: Lane Splitter — for round (Round Oval) and intermediate oval heads.
  • THOR helmets: FLEET fit round (Round Oval) and intermediate oval heads very well.
  • THOR helmets: REFLEX are made for an intermediate oval head, but they also fit a long oval head well.
Head shapes: round oval, intermediate oval, long oval

If you can’t determine your head shape (this sometimes happens), it is most likely an intermediate oval, because a round head shape (equal length and width) is the most obvious.

If your head shape doesn’t match the helmet shape, you need to go one or two sizes up, depending on how big the difference in skull oval is. In that case the liner will fit your skull unevenly and not over its whole area, which has a negative effect on impact energy absorption as well as on the helmet’s noise insulation.

NOTE: The helmet’s inner pads compress with use — keep this in mind when trying it on. The helmet should fit snugly and should not press painfully on your skull. The pressure on your cheeks can be quite strong, and they may be squeezed. The cheek pads are the thickest and compress the most.

We don’t believe you need to wear a helmet for a while to get used to it. A helmet chosen correctly by size and shape fits comfortably and snugly right away — proven by hundreds of customers! The only thing that may be uncomfortable is a tight entry when taking the helmet off and putting it on. Over time the pads at the entry will soften, and the helmet will be much easier to put on and take off. Focus on how your head feels inside the helmet!

REPLACEMENT RECOMMENDATIONS

The recommendation to replace your helmet every five years is based on the consensus of all helmet manufacturers, and the same recommendation applies to all Icon® helmets. Glues of various compositions, rubber parts and other materials used in helmet production can affect the structure of the liner materials over time. Oil from the sebaceous glands of the scalp, sweat, hair products, and ordinary wear and tear also “contribute” over time to the deterioration of the materials the helmet is made of. In addition, petroleum-based ingredients in cleaners, paints and polishes, and constant exposure to gasoline fumes sooner or later have a destructive effect, invisible to the eye, on the helmet materials, which can impair its performance. Practical experience shows that the standards helmet manufacturers follow are revised every five years. This, combined with new advances in material composition, design and manufacturing technologies, naturally leads to the conclusion that it is in the rider’s interest to replace the helmet every five years.

CONSTRUCTION

The ICON® AIRFORM™ helmet meets the safety standards DOT FMVSS 218 (USA), ECE 22.05 (EUROPE), SAI AS1698:2006 (AUSTRALIA) and PSC (JAPAN). These head protection standards are recognized by 50 countries. Before attempting to repair or replace parts on the helmet, refer to the diagram below to familiarize yourself with the specific names and terms used to describe the AIRFORM™ helmet.

  1. // ADJUSTABLE FOREHEAD VENTILATION
  2. // VISOR LOCKING SYSTEM
  3. // VISOR GASKET
  4. // ICON OPTICS™ OUTER VISOR
  5. // DROPSHIELD™ INTERNAL VISOR
  6. // BREATH DEFLECTOR
  7. // FRONT VENT
  8. // SIDE VENTS
  9. // OUTER SHELL
  10. // REAR SPOILER
  11. // EXHAUST VENT
  12. // DUAL-DENSITY EPS LINER
  13. // INTERNAL VISOR LEVER
  14. // VISOR SIDE PLATE
  15. // COMFORT LINER
  16. // RUBBER BASE GASKET

DO NOT MODIFY THE HELMET. To keep this helmet effective, its construction and components must not be altered. Paints and adhesives can damage the helmet without the user noticing and reduce its effectiveness.

SHELL AND EPS

The ICON® AIRFORM PC-ABS helmet shell was created to the strictest quality standards on the market today using polycarbonate extrusion-compression molding. The ICON® AIRFORM dual-density expanded polystyrene liners are designed for maximum absorption and dissipation of impact force. In addition, both liners have a series of directed air channels to distribute airflow from the external ventilation system.

  1. POLYCARBONATE SHELL
  2. EPS LINER 2
  3. EPS LINER 1

FITTING

No helmet can protect against all possible injuries. For your safety, choose a helmet that fits you correctly. For maximum head protection, the helmet must fit snugly and be securely fastened under the chin.

To ensure a proper fit, follow these instructions:

  • Put the helmet on so that it sits low on your forehead. If you cannot see the edge of the eyeport at the top of your field of vision, the helmet is probably not being worn correctly. Adjust the retention system so that when fastened it holds the helmet firmly in place. The size chart is for information only. Always try on a helmet before buying and follow the instructions in this manual to ensure a proper fit.
  • With the chin strap fastened as tightly as possible, hold the helmet with both hands. Without moving your head, try to move the helmet up and down and from side to side. When you try to move the helmet, you should feel the skin on your face and scalp pull. If the helmet moves too easily on your head, it is too big for you. Try a smaller size.
  • With the chin strap fastened, place your palms flat on the back of the helmet and try to roll it off your head forward. Then place your palms on the front of the helmet and try to roll it off backward. If the helmet comes off in either direction, it is either too big or the chin strap is not tight enough. Make sure you have good visibility for operating the motorcycle safely.

CHIN STRAP

For the helmet to work properly, the chin strap must always be fastened when worn. With the chin strap fastened, the helmet must not come off when pulled from the center of the back. Periodically check the chin strap to make sure vibration has not loosened it. To check, simply pull on it a little.

To securely fasten the D-ring retention system, thread the end of the chin strap through the D-rings exactly as shown in the figure below. Fasten the snap on the chin strap to secure the loose end of the strap once it is securely tightened. The only function of the snap at the end of the chin strap is to keep it from flapping in the airflow. It is not part of the retention system. It should be used separately to secure the loose end of the strap.

To unfasten the D-ring retention system, release the loose end of the chin strap from the snap. Then pull the red tab at the end of the lower D-ring to loosen the chin strap. After that, pull the end of the chin strap back through the D-rings to release it completely.

MAKE SURE THE CHIN STRAP IS FASTENED ACCORDING TO THE INSTRUCTIONS ABOVE. MISHANDLING THE STRAP MAY RESULT IN SERIOUS INJURY OR DEATH.

Safe use warning: Do not rely on the chin strap snap alone. It only serves to keep the loose end of the strap out of the way while riding. Fasten the retention system only as shown in the image.

PROPER HELMET USE

SAFETY WARNING: to reduce the risk of serious injury or death, always use the helmet correctly.

  • Never adjust helmet parts while riding. Do this only when fully stopped.
  • Never drop the helmet — dropping it can crack the shell or damage the protective EPS insert. The damage may not be visible. Your helmet is designed for one impact only. For more information, see the “REPLACEMENT RECOMMENDATIONS” section.
  • Never wear anything between your head and the helmet — this may reduce its effectiveness.
  • Do not hang or attach the helmet on any fixtures, including mirrors, handlebars or the passenger grab handle. This can damage the protective EPS insert or liner of the helmet.
  • Never use insect repellent on or around the helmet — it can damage the visor, shell, protective foam and other parts of the helmet.
  • Do not expose the helmet to gasoline or gasoline fumes: they can damage the visor, shell, protective EPS insert and other parts of the helmet.

CHECK YOUR HELMET BEFORE EACH USE

  • Inspect the visor and visor mount — tighten the mounting screws if necessary. Do not overtighten the screws. Overtightening can break the plastic base plate screws or strip the threads of the aluminum screws.
  • Inspect the helmet for damage. If you notice damage or cracks on the helmet, stop using it immediately. For more information, see the “REPLACEMENT TIPS” section. Damage to a helmet resulting from a drop may not be visible.
  • Inspect the helmet for worn or damaged parts. Plastic parts wear out over time. If you find damaged or worn parts, replace them or buy a new helmet. A full list of replacement parts and accessories for the helmet, including liners, cheek pads, side plates, breath deflectors and much more, is available at WWW.RIDEICON.COM
  • Make sure the top liner and cheek pads are correctly installed and the chin strap system is securely fastened.

OUTER VISOR REMOVAL AND INSTALLATION

  1. To remove the visor, open it fully.
  2. Move both locking levers to the “open” position toward the back of the helmet and remove the visor from the toothed base plates.
  3. Once removed, hold the visor in one hand and with the other detach the side plates from the edge of the visor (by the front of the side plate).
  4. Pull each side plate toward you until it separates from the visor.
  5. To replace the visor, line up the tabs on the visor with the notches on the base plates and push it into place until it clicks.
  6. To replace the side plates, line up the tabs on the side plate with the notches on the visor and snap it on. Repeat for each side plate.
  7. Check that the visor opens and closes before riding.

This helmet is not suitable for use with glasses.

SAFE USE WARNING: Do not ride without the side plates attached. If the visor is opened while riding without the side plates, the force of the air acting on the open visor may tear it off the helmet.

INTERNAL VISOR REMOVAL AND INSTALLATION

REMOVAL:

  1. Open the outer visor and lower the internal visor.
  2. Holding the helmet firmly, pull the internal visor forward and down until you hear two clicks and the visor is released from both side clips.

INSTALLATION:

  1. Start by setting the internal visor switch to the DOWN position.
  2. Line up the tabs with the clips of the internal mechanism and press the visor firmly until you hear a click.
  3. Repeat the process on the opposite side of the visor.
  4. Then use the visor switch to check that it is installed correctly, and clean the visor with an ICON Lens cloth or microfiber. Some may find it easier to replace the internal visor after first removing the outer visor and breath deflector. If you decide to remove the outer visor before replacing the internal one, be sure the outer visor is reinstalled correctly. The internal visor is not designed to be used without the outer visor.

SAFE USE WARNING: Incorrect installation of the internal visor may affect its operation.

REMOVING THE COMFORT LINER

To remove the interior parts for cleaning or replacement:

  1. Detach each cheek pad from the helmet by pushing it inward and releasing it from the retention system.
  2. Turn the helmet over and pull out the cheek pads. Note how the cheek pad plate fits between the helmet shell and the EPS liner; this will be useful for reassembly.
  3. Remove the comfort liner by detaching it from the two-snap system at the back of the helmet. Then remove the liner mounting assembly, noting how it fits between the shell and the EPS liner. Remove the side parts of the liner by pushing them inward and releasing them from the retention system.

VENTILATION SYSTEM

To open the forehead vents, slide the switches in the slots up.

RECOMMENDATIONS

ONE-IMPACT RULE — AFTER ANY SEVERE IMPACT, THE HELMET MUST BE REPLACED. Helmets are designed to protect against one impact only. The helmet is designed so that the head is protected in an impact through damage to the shell and EPS liner. In any hard impact on the helmet, the area of the liner that takes the impact absorbs and dissipates the force, which compresses it and damages the liner. The damage may not be visible. Even if no VISIBLE damage is found on the shell, the helmet will be unfit for use after one impact. After an impact, replace the helmet with a new one and dispose of the old one, even if it appears undamaged.

HEARING: wearing any helmet reduces a person’s ability to hear. A person who uses a helmet should be aware that their ability to hear the surrounding world is reduced. Not knowing that hearing is reduced when wearing a helmet may lead to an accident that can cause injury or death.

HELMET WEAR AND DISPOSAL

A helmet has a limited service life and must be replaced when typical signs of wear appear, such as changes in shape, cracks, corrosion, abrasion or other signs of material wear that could lead to helmet damage.

REPLACEMENT TIPS

The advice to replace your helmet every five years is based on the consensus of most helmet manufacturers. Glues, resins and other materials used in helmet production can affect the liner material over time. Skin oils, sweat and cosmetics, as well as normal wear of the materials, also lead to deterioration of the helmet liner. In addition, petroleum-based products in cleaners, paints, fuel and other commonly used substances can damage the materials used in helmet production, potentially impairing their performance. Experience shows that motorcycle helmet quality standards are revised every five years. Combined with statistics on improvements in materials, design and manufacturing methods, this leads to the conclusion that it is in the owner’s interest to replace their helmet at least every five years. After buying a new helmet, dispose of the old one so that it is not reused. Do not sell or give away your old helmet, even if it is undamaged. Over time, the protective layer in a helmet takes the shape of the rider’s head. Such a helmet cannot provide another rider with a comparable level of protection.

RELEASE OF THE MANUFACTURER FROM LIABILITY

No personal protective equipment can protect against all types of injuries in a crash or fall from a motorcycle. No riding gear can provide complete protection against impacts or abrasion in a crash or fall from a motorcycle. Motorcycling is inherently dangerous, and using this helmet cannot prevent injury or death. Even at low speed, a crash can result in serious injury or death. By using this helmet, the user assumes all risks associated with this activity that may result in injury or death. The user hereby waives all claims and lawsuits against Icon® Motosports, Lemans Corporation and J-TECH Corp in the event of death or injury resulting from the use of Icon Motosports products.

The Mips® safety system

A technology, built into helmets and designed to help reduce rotational motion to the head that could occur in so-called oblique impacts.

We have over 25 years of research into rotational motion and helmet safety, and an abundance of studies and data that say the same thing: in the vast majority of accidents in which someone hits their head, the impact is oblique, and an oblique impact entails an increased risk of brain damage. The same thing goes for objects falling from above at, for instance, a building site: they cause an oblique impact — even if you are standing still.

Mips means addressing the rotational motion

The moment your head hits the ground at an angle, rotational motion can make the head rotate more or less, depending on the impacting object or surface. The energy from the impact can be directed further into the head, which can cause brain injury. Rotational motion is thus the result of oblique impacts to the head.

The brain is more sensitive to oblique impacts versus straight impacts. Oblique impacts are also much more common. But most helmets on the market today are only tested and approved for straight impacts, even though these kinds of accidents are far less common.

Designed to help reduce rotational motion to the head in oblique impacts

Everything revolves around the Mips low-friction layer. It mimics the brain’s own protective system, which allows the brain to move slightly inside the head. The Mips system is designed to work on the same principle. The low-friction layer is built into the helmet and makes the energy-absorbing layers (the “padding”) mobile so that the head can move 10–15 mm inside the helmet on impact.

The Mips® safety system is available in different designs for different areas of use, but the principle is the same for all options. The system is attached to the helmet with elastic material, ensuring that the low-friction bearing is always in the proper position. The low-friction bearing has also been specially engineered to fit each helmet model and size and is injection-molded to fit perfectly inside each individual helmet. It provides a minimalist, fully integrated design that neither interferes with the helmet’s fit nor affects the weight more than marginally. A Mips system weighs between 20 and 45 grams.

Mips® safety system — a bright idea based in science

Mips is a technology that is based on many years of research into the brain and brain damage, and we are firmly rooted in science. Our story begins in 1995, when brain surgeon Hans von Holst from Karolinska Institutet in Stockholm, Sweden, began researching helmet construction. He based his research on the realization that the helmets available at the time did not offer sufficient protection against brain damage. He contacted the KTH Royal Institute of Technology in Stockholm to initiate biomechanical research on the prevention of head and neck injuries.

The initiative led to what is now recognized as one of the most important Finite Element (FE) models of the human brain in the world. The model is an important research tool for Mips when it comes to visualizing and measuring the effects of the Mips system. Our first product was a proprietary riding helmet launched in 2007. Since then, Mips has become an “ingredient brand,” which means we sell our technology to other manufacturers, who in turn incorporate it into their products. Today, our safety systems are found in helmets for everything from skiing and cycling to construction and industry.

Recommend
Magazine Icon Motosports Brand Protection Magazine Wheelie: Trick Theory Stunt Show with Girls Baldini Stunt Show