Podolsk,
14 Lobacheva st.
To contact page
RU EN
Tue-Fri 11:00-20:00
Sat-Sun 11:00-17:00
Mon - Closed
Airflite Inky
Мотошлем интеграл
Airflite Inky
Airflite Inky
Airflite Inky
Airflite Inky
Airflite Inky
Airflite Inky
Out of stock

С мотошлемом AIRFLITE INKY все мы поднимаемся на борт плавучей базы ICON и распеваем забойные морские шлягеры. Неужели случилось так, что мы все думали о себе как о Себастьяне, а о тебе — как об Ариэле? Были ли мы сами Ариэлем, а ты — неизвестным сокровищем, скрытым в морских глубинах? Неужели еще не всем известно, что лучше там, где глубже? Что там с этой башней на крышке коробки? Так много вопросов без ответа, что даже эта изумительная графика не даст даже и намека на ответ.

  • Соответствует требованиям стандартов безопасности для мотошлемов DOT FMVSS (США), ECE 22.05 (Европа) и PCS (Япония). Не отгружается со стикерами с сертификацией PCS, если только не приобретается у авторизованного дилера в этой стране.
  • Поставляется с голубым внутренним визором RST DropShield и с прозрачным быстрозаменяемым визором с противотуманным покрытием FlightShield.
  • Съемная мягкая подкладка из гигроскопичного материала HydraDry.
  • Поликарбонатная скорлупа, выполненная методом литья под давлением для высокой прочности.

HELMET REPLACEMENT RECOMMENDATIONS

The recommendation to replace your helmet every five years is based on the consensus of all helmet manufacturers, and the same recommendation applies to all Icon® helmets. Glues of various compositions, rubber parts and other materials used in helmet production can affect the structure of the liner materials over time. Oil from the sebaceous glands of the scalp, sweat, hair products, and ordinary wear and tear also “contribute” over time to the deterioration of the materials the helmet is made of. In addition, petroleum-based ingredients in cleaners, paints and polishes, and constant exposure to gasoline fumes sooner or later have a destructive effect, invisible to the eye, on the helmet materials, which can impair its performance. Practical experience shows that the standards helmet manufacturers follow are revised every five years. This, combined with new advances in materials, design and manufacturing technologies, naturally leads to the conclusion that it is in the rider’s interest to replace the helmet every five years.

HELMET CONSTRUCTION

The ICON® AIRFLITE™ helmet is designed to the ICON WORLD STANDARD, which also meets the requirements of DOT FMVSS 218 (USA), ECE 22.05 (EUROPE), SAI AS1698:2006 (AUSTRALIA) and PSC (JAPAN). These head protection standards are recognized by 50 countries. Before attempting to repair or replace parts on the helmet, refer to the diagram below to familiarize yourself with the specific names and terms used to describe the AIRFLITE™ helmet.

  • 1. // EXTERNAL VENT
  • 2. // VISOR LOCKING SYSTEM
  • 3. // EYEPORT GASKET
  • 4. // FLITESHIELD™ OUTER VISOR
  • 5. // DROPSHIELD™ INTERNAL VISOR
  • 6. // SIDE PLATES
  • 7. // BREATH DEFLECTOR
  • 8. // MOUTH VENT
  • 9. // SAFETY LOCK BUTTON
  • 10. // OUTER SHELL
  • 11. // REAR SPOILER
  • 12. // REAR EXHAUST VENT
  • 13. // DUAL-DENSITY EPS LINER
  • 14. // VISOR SWITCH
  • 15. // COMFORT LINER
  • 16. // CHEEK PADS
  • 17. // NOISE-REDUCING INSERTS
  • 18. // BASE GASKET

DO NOT MODIFY THE HELMET. To keep this helmet effective, its construction and components must not be altered. Paints and adhesives can damage the helmet without the user noticing and reduce its effectiveness.

SHELL AND EPS

The ICON® AIRFLITE PC-ABS helmet shell was created to the strictest quality standards on the market today using polycarbonate extrusion-compression molding. The ICON® AIRFLITE dual-density expanded polystyrene liners are designed for maximum absorption and dissipation of impact force. In addition, both liners have a series of directed air channels to distribute airflow from the external ventilation system.

  1. POLYCARBONATE SHELL
  2. EPS LINER 2
  3. EPS LINER 1

SAFE USE WARNING: Do not buy a used helmet or use someone else’s helmet. Over time, the protective foam in a helmet takes the shape of the owner’s head. A previously used helmet will not provide the same level of protection as a new one. An incorrectly sized helmet can increase the risk of serious injury or death in a crash. A helmet that is too large may shift or come off the head in a crash. To choose a helmet of the right size, follow the instructions below.

FITTING

No helmet can protect against all possible injuries. For your safety, choose a helmet that fits you correctly. For maximum head protection, the helmet must fit snugly and be securely fastened under the chin.

To ensure a proper fit, follow these instructions:

  • Put the helmet on so that it sits low on your forehead. If you cannot see the edge of the eyeport at the top of your field of vision, the helmet is probably not being worn correctly. Adjust the retention system so that when fastened it holds the helmet firmly in place. The size chart is for information only. Always try on a helmet before buying and follow the instructions in this manual to ensure a proper fit.
  • With the chin strap fastened as tightly as possible, hold the helmet with both hands. Without moving your head, try to move the helmet up and down and from side to side. When you try to move the helmet, you should feel the skin on your face and scalp pull. If the helmet moves too easily on your head, it is too big for you. Try a smaller size.
  • With the chin strap fastened, place your palms flat on the back of the helmet and try to roll it off your head forward. Then place your palms on the front of the helmet and try to roll it off backward. If the helmet comes off in either direction, it is either too big or the chin strap is not tight enough. Make sure you have good visibility for operating the motorcycle safely.

CHIN STRAP

For the helmet to work properly, the chin strap must always be securely fastened when worn. With the chin strap fastened, the helmet must not come off when pulled from the center of the back. Periodically check the chin strap to make sure vibration has not loosened it. To check, simply pull on it a little.

To securely fasten the D-ring retention system, thread the end of the chin strap through the D-rings exactly as shown in the figure below. Fasten the snap on the chin strap to secure the loose end of the strap once it is securely fastened. The only function of the snap at the end of the chin strap is to keep it from flapping in the airflow. It is not part of the retention system. It should be used separately, without threading through the D-rings, as shown below.

To unfasten the D-ring retention system, release the loose end of the chin strap from the snap. Then pull the red tab at the end of the lower D-ring to loosen the chin strap. After that, pull the end of the chin strap back through the D-rings to release it completely.

MAKE SURE THE CHIN STRAP IS FASTENED ACCORDING TO THE INSTRUCTIONS ABOVE. MISHANDLING THE STRAP MAY RESULT IN SERIOUS INJURY OR DEATH.

SAFE USE WARNING: Do not rely on the chin strap snap alone. It only serves to keep the loose end of the strap out of the way while riding. Fasten the retention system only as shown in the image.

PROPER HELMET USE

SAFETY WARNING: to reduce the risk of serious injury or death, always use the helmet correctly.

  • Never adjust helmet parts while riding. Do this only when fully stopped.
  • Never drop the helmet — dropping it can crack the shell or damage the protective foam. The damage may not be visible. Your helmet is designed for one impact only. For more information, see the “REPLACEMENT RECOMMENDATIONS” section.
  • Never wear anything between your head and the helmet — this may reduce its effectiveness.
  • Do not hang or attach the helmet on any fixtures, including mirrors, handlebars or the passenger grab handle. This can damage the protective foam or liner of the helmet.
  • Never use insect repellent on or around the helmet — it can damage the visor, shell, protective foam and other parts of the helmet.
  • Do not expose the helmet to gasoline or gasoline fumes: they can damage the visor, shell, protective foam and other parts of the helmet.

CHECK YOUR HELMET BEFORE EACH USE

  • Inspect the visor and visor mount — tighten the mounting screws if necessary. Do not overtighten the screws. Overtightening can break the plastic base plate screws or strip the threads of the aluminum screws.
  • Inspect the helmet for damage. If you notice damage or cracks on the helmet, stop using it immediately. For more information, see the “REPLACEMENT TIPS” section. Damage to a helmet resulting from a drop may not be visible.
  • Inspect the helmet for worn or damaged parts. Plastic parts wear out over time. If you find damaged or worn parts, replace them or buy a new helmet. A full list of replacement parts and accessories for the helmet, including liners, cheek pads, side plates, breath deflectors and much more, is available at WWW.RIDEICON.COM
  • Make sure the liner and cheek pads are correctly installed and the chin strap system is securely fastened.

OUTER VISOR REMOVAL AND INSTALLATION

REMOVAL:

  1. To remove the visor, first remove the side plates by firmly grasping them at the front and top and pulling outward. The two angled pins on each side plate should pop out of the holes in the shell.
  2. Once the side plates are removed, fully open the visor and keep lifting until it reaches its fully open limit — at this point the holes in the visor line up with the latches on the pivot mount, allowing the visor to be easily removed

INSTALLATION:

  1. To install the FliteShield™, line up the pivot holes with the posts while holding the shield in the fully open position. Push each pivot hole onto the posts to lock them in place, and rotate the shield forward to the fully closed position.
  2. Reinstall the side plates by lining up the side plate pins with the holes in the shell and pushing them toward the helmet.

SAFE USE WARNING: Do not ride without the side plates attached. If the shield opens while riding without the side plates, the force of the air acting on the open visor may tear it off the helmet.

INTERNAL VISOR REMOVAL AND INSTALLATION

REMOVAL:

  1. Open the outer visor and lower the internal visor.
  2. Holding the helmet firmly, pull the internal visor forward and down until you hear two clicks and the visor is released from both side clips.

INSTALLATION:

  1. Start by setting the internal visor switch to the DOWN position.
  2. Line up the tabs with the clips of the internal mechanism and press the shield firmly until you hear a click.
  3. Repeat the process on the opposite side of the visor.
  4. Then use the visor switch to make sure it is installed correctly, and clean the visor with an ICON Lens cloth or microfiber. Some may find it easier to replace the internal visor after first removing the outer visor and breath deflector. If you decide to remove the outer visor before replacing the internal one, be sure the outer visor is reinstalled correctly. The internal visor is not designed to be used without the outer visor.

SAFE USE WARNING: Incorrect installation of the internal visor may affect its operation.

INTERIOR PARTS

The Airflite helmet has a fully replaceable set of interior parts covered with Icon®’s exclusive moisture-wicking HydraDry™ material. Helmet size is determined by three factors: the size of the outer shell, the thickness of the inner EPS liner and the thickness of the interior components. You can achieve a more comfortable fit by replacing the existing cheek pads with thinner ones (for more room) or thicker ones (for less room). To order replacement parts, contact your local dealer or visit www.rideicon.com.

REMOVING THE COMFORT LINER

To remove the interior parts for cleaning or replacement:

  1. Detach each cheek pad from the helmet by pushing it inward and releasing it from the retention system.
  2. Turn the helmet over and pull out the cheek pads. Note how the cheek pad plate fits between the helmet shell and the EPS liner; this will be useful for reassembly.
  3. Remove the comfort liner by detaching it from the two-snap system at the back of the helmet. Then remove the liner mounting assembly, noting how it fits between the shell and the EPS liner. Remove the side parts of the liner by pushing them inward and releasing them from the retention system.

VENTILATION SYSTEM

To open the vents, slide the switches in the slots shown in Fig. 1 to the “open” position. To open the forehead vents (Fig. 2), slide the switches in the slots backward.

RECOMMENDATIONS

ONE-IMPACT RULE — AFTER ANY SEVERE IMPACT, THE HELMET MUST BE REPLACED. Helmets are designed to protect against one impact only. The helmet is designed so that the head is protected in an impact through damage to the shell and EPS liner. In any hard impact on the helmet, the area of the liner that takes the impact absorbs and dissipates the force, which compresses it and damages the liner. The damage may not be visible. Even if no VISIBLE damage is found on the shell, the helmet will be unfit for use after one impact. After an impact, replace the helmet with a new one and dispose of the old one, even if it appears undamaged.

HEARING: wearing any helmet reduces a person’s ability to hear. A person who uses a helmet should be aware that their ability to hear the surrounding world is reduced. Not knowing that hearing is reduced when wearing a helmet may lead to an accident that can cause injury or death.

HELMET WEAR AND DISPOSAL

A helmet has a limited service life and must be replaced when typical signs of wear appear, such as changes in shape, cracks, corrosion, abrasion or other signs of material wear that could lead to helmet damage.

REPLACEMENT TIPS

The advice to replace your helmet every five years is based on the consensus of most helmet manufacturers. Glues, resins and other materials used in helmet production can affect the liner material over time. Skin oils, sweat and cosmetics, as well as normal wear of the materials, also lead to deterioration of the helmet liner. In addition, petroleum-based products in cleaners, paints, fuel and other commonly used substances can damage the materials used in helmet production, potentially impairing their performance. Experience shows that helmet quality standards are revised every five years. Combined with statistics on improvements in materials, design and manufacturing methods, this leads to the conclusion that it is in the owner’s interest to replace their helmet at least every five years. After buying a new helmet, dispose of the old one so that it is not reused. Do not sell or give away your old helmet, even if it is undamaged. Over time, the protective layer in a helmet takes the shape of the rider’s head. Such a helmet cannot provide another rider with a comparable level of protection.

RELEASE OF THE MANUFACTURER FROM LIABILITY BY THE PRODUCT OWNER

No personal protective equipment can protect against all types of injuries in a crash or fall from a motorcycle. No riding gear can provide complete protection against impacts or abrasion in a crash or fall from a motorcycle. Motorcycling is inherently dangerous, and using this helmet cannot prevent injury or death. Even at low speed, a crash can result in serious injury or death. By using this helmet, the user assumes all risks associated with this activity that may result in injury or death. The user hereby waives all claims and lawsuits against Icon® Motosports, Lemans Corporation and J-TECH Corp in the event of death or injury resulting from the use of Icon Motosports products.

Recommend
Magazine Street Glide Arlen Ness Fork Stunt Show with Girls Magazine Ouest Bike Show 2023 Magazine XSR125 Dominator