Podolsk,
14 Lobacheva st.
To contact page
RU EN
Tue-Fri 11:00-20:00
Sat-Sun 11:00-17:00
Mon - Closed
AIRFORM RETRO WM
Ladies textile motorcycle jacket
AIRFORM RETRO WM
AIRFORM RETRO WM
AIRFORM RETRO WM
AIRFORM RETRO WM
AIRFORM RETRO WM
AIRFORM RETRO WM

See the jacket measurements in the “Size” tab below.

RUB 23,100 RUB 18,800

Modesty aside, ICON is very good at hoods. The Airform™ ladies jacket comes with the iconic hood, which stows away for high-speed riding. The relaxed-fit chassis is made of lightweight reinforced polyester and equipped with a full set of D3O® impact protectors (elbows, shoulders, back). Offering enough protection for light showers, the Airform jacket has a WP1 water resistance rating. It adapts easily to hot summer riding thanks to four zippered intake/exhaust vents. It also features an AirFly™ center mesh vent for maximum airflow. Comfort, style and all-season performance from the brand that invented the hooded motorcycle jacket.

FIT

  • ICON® women’s sport fit.

MATERIAL

  • Durable 420D polyester chassis with internal reinforcements.

PROTECTION

  • The jacket is tested and certified to EN 17092-4:2020 Class A.
  • Removable D3O® Viper 1 CE back protector certified to EN 1621-2:2014, Level 1 T-.
  • Removable D3O® LP1 CE shoulder and elbow protectors certified to EN 1621-1:2012, Level 1, T-, T+.

FEATURES

  • Center front packable AirFly™ mesh panel, zippered vents on the chest and back, packable hood, zippered cuff vents, WP1 water resistance level.

GENERAL CARE RECOMMENDATIONS

All Icon motorcycle jackets are tough and can withstand even hard contact with asphalt, but of course no jacket in the world can remain undamaged in every possible crash. If you happen to be in an accident, when you get home carefully inspect the jacket for significant structural damage, namely heavy abrasion, holes, damaged seams, etc. If there is such structural damage, the jacket must be replaced.

Try not to expose the jacket to excessive direct sunlight or ultraviolet radiation. This is especially important during long-term storage. Always store your jacket in a dark, well-ventilated place. It is best to store the jacket on a hanger with wide shoulders, preferably with foam padding. Do not put the jacket in a plastic bag or a cover made of another airtight material, because the leather parts of the jacket need to “breathe” during storage, otherwise they may be damaged by mold or rot. Finally, do not expose the jacket (or any other riding gear) to gasoline fumes and gasoline combustion gases, or to fumes from other harmful chemicals. Long-term exposure to these fumes weakens the internal structure of nylon, polyester and leather, reducing the protective properties of the jacket even though it still looks just as great on the outside.

PREPARING FOR CLEANING

Before you actually clean and wash the jacket, you need to take a few preliminary steps:

  • First of all, detach the removable liner from the jacket (if any). When detaching the liner, undo each snap separately WITHOUT using excessive force, otherwise you risk breaking the fasteners.
  • Remove all removable protectors from the jacket. Be sure to close all hook-and-loop fasteners on the flaps of the pockets you removed the protective plates from.

WASHING AND CLEANING

Hand wash the removable liner in warm water (30°C) with a mild detergent. Rinse the removable liner thoroughly in clean water until all traces of detergent are gone. If you want to clean the protectors, wipe their plastic surfaces with a damp cloth.

Textile motorcycle jackets should be hand washed in warm water (30°C) with a mild detergent. Hand washing keeps mechanical stress during washing to a minimum. A soft toothbrush is great for removing traces of kamikaze bugs that collided with you on the road, or street dirt. Rinse the jacket in clean water until all traces of detergent are removed. DO NOT USE washing powders with active oxygen, bleach, fabric softeners or dry cleaning chemicals. All of these can damage the jacket.

DRYING THE JACKET

After washing, do not wring or twist the removable liner. Hang it on a drying rack until the water has completely drained. DO NOT tumble dry, dry in direct sunlight, or dry with hair dryers or heaters of any kind.

After washing, the jacket can be dried in only one way — hung on a hanger until the water has drained and it is dry. Do not dry the jacket in direct sunlight or use hair dryers and heaters to speed things up. Do not iron the jacket — neither the whole jacket nor any of its parts. DO NOT USE a tumble dryer to dry the jacket.

D3O® is the number one choice for motorcycle body armor and protective gear that delivers outstanding impact protection, comfort and flexibility. From MotoGP, to off-road and the street, our innovative range of CE Level 1 and Level 2 certified products are trusted and sold worldwide by leading motorcycle brands.

HOW DOES MOTORCYCLE ARMOR WORK?

Motorcycle armor works by absorbing the shock from an impact. Rather than the impact striking your body with full force, motorcycle armor helps take the brunt of the impact and dissipate the force to reduce its severity. The impact protection material found in motorcycle armor is what makes this possible, and the materials used in and around the armor (such as leather in a jacket, or woven kevlar in motorcycle pants) help to resist abrasion.

D3O® motorcycle armor offers the most advanced impact protection available on the market. Based on non-Newtonian principles, D3O® materials are soft and flexible in their resting state, but stiffen under an impact to disperse the energy of the force across the surface area of the product. D3O® armor is durable and designed to withstand multiple impacts, only needing to be replaced when showing wear and tear. This is in contrast to other armor which can flatten out over time, quickly losing its ability to protect effectively.

The design of motorcycle armor is also key to ensure it gives maximum levels of protection and comfort. Each piece of D3O® armor is designed to fit specific parts of the body comfortably, including the back, chest and limbs, such as knees and elbows. This gives these areas optimum coverage and reduces the likelihood of injury.

WHAT EN NUMBERS TO LOOK FOR ON MOTORCYCLE ARMOR?

When looking at your D3O® impact protection or the label in your motorcycle armor, you're likely to see EN (European Norm) numbers. EN standards are used to help demonstrate that a product meets the requirements of the PPE Regulation (EU) 2016/425 or PPE Regulation (2016/425) as brought into UK Law and amended.

  • D3O® Ghost™, LP1 and LP2 are CE/UKCA certified in accordance with EN1621-1:2012.
  • D3O® Viper Stealth, Central and Pro Back protectors are certified in accordance with EN1621-2:2014.
  • D3O® knuckle protection is tested to EN13594:2015.
  • D3O® Ankle protection is certified in accordance with EN 13634:2015.
  • The D3O® CP1 Chest Protector and Racing Chest Protector are certified in accordance with EN1621-3:2018.

EN1621 relates specifically to motorcycle armor. EN1621-1:2012 relates to limb protection, EN1621-2:2014 to back protection, and EN1621-3:2018 to chest protection. All of these can be tested to meet Level 1 or Level 2 protection. Level 1 offers a good level of impact protection, and Level 2 meets the criteria for racing, and can therefore withstand higher force impacts.

EN13594:2015 is specific to motorcycle glove protection. To pass, the product must meet the following criteria: Innocuousness, ergonomic requirements, sizing and cuff length, restraint, tear strength, seam strength, impact abrasion resistance, cut resistance, and impact protection of knuckles.

EN13634:2015 applies to motorcycle footwear. The criteria that need to be met include: protection, ergonomic characteristics, innocuousness, mechanical properties, marking and information for users.

Whole garment testing is reviewed against EN 17092:2020. This is separate from the EN standards indicated above. While impact protection is necessary to meet EN 17092:2020, the armor also needs to be tested on its own to ensure it's fit for purpose and meets Level 1 or Level 2 requirements.

EN17092 is tested to 5 levels of criteria. The testing looks at the different zones on the body and how well the armor protects those areas under force. Garments certified to EN17092 and featuring D3O® impact protection are therefore some of the safest and most well-tested motorcycle armor items available on the market. You can be guaranteed regulated, independent testing when looking for these EN standards.

WHAT DOES AAA-A CLASSIFICATION MEAN?

The AAA-A garment classification is important to check and understand so you make sure you're getting the correct level of protection.

AAA-A classes are certified in accordance with EN 17092:2020. The materials are tested under lab conditions to assess how much speed and force they can withstand before tearing — this is the measure of abrasion resistance. This then allows the AAA-A classification to be assigned.

  • AAA — the highest class possible, AAA is suitable for track racing. Limb protection is mandatory in AAA garments, and back and chest protection are optional. D3O® LP2 limb protectors, the Viper Pro back protector and Racing Chest are great examples of the best armor setup to hit AAA. CE EN 1621-1:2012 limb protection and CE EN 1621-2:2014 back and chest protection are the marks to look out for.
  • AA — best for touring and long-distance riding. This still requires CE EN 1621-1:2012 Level 1 impact protection at the shoulders, elbows, hips and knees. Back and chest protectors are optional but worth the investment. D3O® LP1 limb and Viper Stealth back protectors are great options to consider.
  • A — suitable for urban riding, commuting, and weekend cruising. Bike jeans and other textile-type pants are most likely to be Class A. This requires CE EN 1621-1:2012 Level 1 impact protection at the shoulders, elbows and knees, with hips becoming optional. D3O® Ghost™ is the perfect fit-and-forget armor for more casual riding.

The main difference between the classes is the abrasion, seam strength and cut resistance of the garment. The more you go towards AAA, the better the materials and construction.

D3O works with many partner brands to provide market-leading impact protection armor in motorcycle clothing.

WHAT IS THE DIFFERENCE BETWEEN LEVEL 1 AND LEVEL 2 MOTORCYCLE ARMOR?

D3O® motorcycle impact protection is offered in two levels, Level 1 and Level 2. Choose the right level of protection depending on the type of riding you're doing, as well as taking into consideration the technical features you prefer to have while riding.

  • Level 1 — suitable for most types of riding, Level 1 can be used by urban, commuter, and touring motorcyclists offering them a great level of all-around protection.
  • Level 2 — best suited to bikers racing on tracks, riding more extreme off-road, or stunt riding. Level 2 can provide up to 50% more impact protection than level 1.

D3O offers a range of CE/UKCA armor to protect your chest, back and limbs whilst riding to minimize the likelihood of injury from riding accidents.

PPE:

Icon® motorcycle gloves are considered personal protective equipment (PPE) under EU Directive 89/686/EEC. The motorcycle gloves described in this manual are Category II PPE, so the CE marking may be applied to them only after obtaining a CE certificate of conformity and subsequent certification by an EU notified body. The CE marking on protective gloves indicates compliance with the basic health and safety requirements of Directive 89/686/EEC and/or the essential health and safety requirements of Regulation (EU) 2016/425. The protective gloves have passed CE type-examination testing at the notified body Ricotest s.r.l, No. 0498, for compliance with Directive 89/686/EEC and/or Regulation (EU) 2016/425. In addition, this protective equipment has been inspected and tested for compliance with the following technical standards: EN 13594:2015 “Protective gloves for motorcycle riders — requirements and test methods”.

PROHIBITIONS AND LIMITATIONS OF USE:

Icon® motorcycle gloves are intended for use only as motorcycle gloves. Icon® motorcycle gloves may be used only for riding road motorcycles. Icon® motorcycle gloves are designed to provide limited protection only in certain circumstances. Icon® motorcycle gloves are intended for use in combination with other protective equipment. Using Icon® motorcycle gloves in combination with any other PPE or motorcycle riding gear does not mean that such PPE or riding gear complies with CE standards. For additional protection when riding a motorcycle, Icon® strongly recommends always using several mutually compatible PPE items, including a certified helmet, a jacket with shoulder and elbow impact protection, a certified back protector, pants with certified knee, shin and hip impact protectors, certified gloves and boots. Motorcycling is dangerous, so using Icon® motorcycle gloves cannot prevent injury or death. The level of risk or danger a rider will face is closely related to their riding style and the type of crash. Riders should choose their protective motorcycle gloves carefully according to the nature of their riding and the level of risk they are exposed to.

CE MARKING WARNINGS

Below is an example of the CE marking and other markings on Icon® motorcycle gloves in accordance with Directive 89/686/EEC, Regulation (EU) 2016/425 and EN 13594:2015. The CE marking is shown on a label attached to the gloves.

Example of the CE marking on Icon motorcycle gloves

MARKING EXPLAINED

CE
The CE marking indicates that the protective gloves comply with the basic health and safety requirements of Directive 89/686/EEC and/or the essential health and safety requirements of Regulation (EU) 2016/425.

Open book pictogram
Pictogram indicating that a user manual (information sheet) is supplied with this product.

Motorcyclist pictogram
Special symbol indicating that the protective gloves are intended for motorcycle riding only.

1 or 2
Performance level of the protective gloves according to EN 13594:2015 during testing.
1 or 2 means the gloves meet the minimum requirements for cuff length, restraint straps, tear strength, seam strength, cut resistance and abrasion resistance for protection level 1 or 2.
Level 1 gloves: protection level 1 is considered the minimum level required for effective protection in a crash. Gloves of this level provide an optimal level of comfort for any riding style.
Level 2 gloves: level 2 is a higher level of protection, but stronger protection means heavier gear and less comfort, so this level is not suitable for every rider.

KP
KP is a special designation indicating that the gloves meet the requirements for knuckle impact protection for the stated protection level. If this field is left blank, the test was not carried out.
For level 1 gloves, knuckle impact protection is optional.
For level 2 gloves, knuckle impact protection is mandatory.
For more information on the performance level of these protective gloves, see the “Performance” section of this manual and Table 2 “Type tests of motorcycle gloves for compliance with the minimum requirements of EN 13594:2015” in that section.

EN 13594:2015
Technical standard

Icon logo
Manufacturer’s name or logo

PRODUCT NAME
Name or internal technical code of the protective gloves

GLOVE SIZE
Size of the protective gloves. See the size tables in the “PPE fit” section of this manual.

M / W
M = men’s gloves
W = women’s gloves

In addition to the markings described above, other coded data that Icon® uses for its products may be present. Coding may also appear in other versions of the marking.

PROTECTION LIMITATIONS

Icon® motorcycle gloves protect the user from external conditions without impairing their ability to operate the motorcycle’s hand controls. Icon® motorcycle gloves are designed for safety and freedom of movement. Icon® motorcycle gloves are classed as PPE because they are designed to provide limited protection of the hands in a crash or fall from a motorcycle. Additional dangers in road accidents involving a motorcycle may come from impacts with the motorcycle and collisions with other vehicles and objects on the road. The likelihood of serious injury increases if the hand becomes trapped under the motorcycle while sliding. Icon® motorcycle gloves do not prevent injuries caused by heavy impacts, injuries caused by severe bending, twisting, torsion or crushing from hitting an object, injuries caused by very sudden movements, or extensive penetrating injuries. The force levels used in testing cannot be directly compared with the forces riders are exposed to in real crashes, so products that meet EN 13594:2015 can only reduce the severity of some minor injuries. No protective gloves can provide complete protection against all injuries. The principle is to create a product that helps reduce the risk of injury to the area this PPE was designed to provide limited protection for.

PPE FIT:

For maximum protection, PPE must be worn so that it securely covers vulnerable areas of the body. If the PPE design includes protective features, the PPE must fit the user correctly to be positioned properly.

The correct fit of protective gloves is very important. The fit of different types of protective gloves varies depending on design and construction. Use only protective gloves that fit your hands precisely. Do not use protective gloves of the wrong size. Motorcycle gloves should be worn over or under the jacket sleeves so that the jacket sleeves and glove cuffs overlap.

Motorcycle glove size usually depends on palm circumference. To choose the right size of Icon® motorcycle gloves, measure your palm circumference. Compare your measurements with the table below to determine your approximate size. If the glove in the selected size does not fit, try a larger or smaller size.

Men’s sizes

SMLXL2XL3XL4XL
cm16.5–17.819.1–20.321.6–22.924.1–25.426.7–27.929.2–30.531.8–33.0
inches6.5–77.5–88.5–99.5–1010.5–1111.5–1212.5–13

Women’s sizes

XSSMLXL2XL
cm14.6–15.315.9–16.517.1–17.818.4–19.119.7–20.321.0–21.6
inches5.75–6.06.25–6.56.75–7.07.25–7.57.75–8.08.25–8.5

Make sure the gloves do not interfere with operating the motorcycle. For maximum protection and safety, protective gloves must not cause discomfort or restrict the rider’s freedom of movement, or prevent access to and use of the motorcycle controls in the normal riding position. If you cannot find comfortable protective gloves of this type, use another type of CE-certified protective gloves.

PERFORMANCE

Icon® protective motorcycle gloves have passed CE type-examination testing for compliance with Directive 89/686/EEC and/or Regulation (EU) 2016/425. In addition, they have been inspected and tested for compliance with the appropriate technical standard. The European standard EN 13594:2015 provides for two levels of protection depending on the protective features. The level of risk or danger a rider will face is closely related to their riding style and the type of crash. According to EN 13594:2015, protection level 1 is considered the minimum level required for effective protection in a crash. Gloves of this level provide an optimal level of comfort for any riding style. If the rider’s riding style or sport involves increased risk, level 2 protective equipment with a higher level of protection is recommended. However, stronger protection means heavier gear and less comfort, so this level is not suitable for every rider.

TABLE 2. TYPE TESTS OF MOTORCYCLE GLOVES FOR COMPLIANCE WITH THE MINIMUM REQUIREMENTS OF EN 13594:2015

TestStandardUnitLevel 1Level 2
Cuff lengthClause 4.5mm≥ 15≥ 50
Restraint strapClause 4.6N≥ 25≥ 50
Tear strength (protective layer)Clause 4.7N
Palm and palm side of fingers≥ 25≥ 35
Cuff, back of hand and back of fingers≥ 18≥ 30
Fourchettes (panels between fingers)≥ 18≥ 25
Seam strength (protective layer)Clause 4.8N/mm
Main seams≥ 6≥ 10
Fourchettes (panels between fingers)≥ 4≥ 7
Cut resistance (all layers)Clause 4.9index
Palm side≥ 1.2≥ 1.8
Back sideNot required≥ 1.2
Abrasion resistance (palm side, all layers): see Fig. 1Clause 4.10seconds
Single test time≥ 3.0≥ 6.0
Average abrasion time≥ 4.0≥ 8.0
Knuckle protection (optional for level 1)Clause 4.11kN
Single impact≤ 9.0≤ 5.0
Mean impact force≤ 7.0≤ 4.0
The glove area on which the abrasion resistance test was carried out

FIG. 1. THE GLOVE AREA ON WHICH THE ABRASION RESISTANCE TEST WAS CARRIED OUT

  • l = total length from wrist to fingertip
  • C = center of the tested area
  • a = distance from the wrist line to C (18% of l, +/- 3 mm)
  • b = distance from the side edge to C (13% of l, +/- 3 mm)

In the event of a mechanical impact or crash:

In the event of an impact or crash, key parts of the protective gloves may be damaged, and the gloves may no longer provide limited protection against the impacts described in the “Prohibitions and limitations of use”, “Performance” and “Protection limitations” sections. Damage may not be visible on simple visual inspection. In the event of an impact or crash, the gloves should be replaced. New motorcycle gloves can be purchased from Icon® retailers.

Two-year rule:

As a rule, lightweight PPE such as Icon® motorcycle gloves should be replaced every two years, even if there is no visible damage. Damage may not be visible on simple visual inspection.

Disposal:

At the end of their service life, Icon® motorcycle gloves should not be thrown away with household waste. Dispose of the gloves according to local disposal requirements.

RELEASE OF THE MANUFACTURER FROM LIABILITY BY THE PRODUCT OWNER

NO PERSONAL PROTECTIVE EQUIPMENT CAN PROVIDE PROTECTION AGAINST ALL TYPES OF IMPACTS. NO RIDING GEAR CAN PROVIDE COMPLETE PROTECTION AGAINST ALL TYPES OF INJURIES. MOTORCYCLING IS INHERENTLY DANGEROUS, AND USING THIS GEAR CANNOT PREVENT INJURY OR DEATH. BY USING THIS GEAR, THE USER ASSUMES ALL RISKS ASSOCIATED WITH THIS ACTIVITY THAT MAY RESULT IN INJURY OR DEATH. THE USER HEREBY WAIVES ALL CLAIMS AND LAWSUITS AGAINST Icon® (A DIVISION OF LEMANS CORPORATION) AND LEMANS CORPORATION IN THE EVENT OF DEATH OR INJURY RESULTING FROM THE USE OF Icon® PRODUCTS.

When choosing a size, compare the measurements in the table with those of a garment you find comfortable. Keep in mind that riding gear has built-in protection and denser materials.

On our forum we share experience of choosing motorcycle jackets remotely.

Outerwear measurement diagram, front view
Front view

The table below shows the outer dimensions in centimeters, measured with a tape measure. The jacket lies freely on a table in its natural position. [A] — length of the front zipper. [C] — distance from the sleeve edge to the collar-shoulder seam.

A B C D E
XS 54 49 70 45.5 46
S
M 60 49 73 50 52
L 61 47.5 73.5 53.5 56
XL 62.2 47 75 57.5 61
2XL 63 45.5 76 61.5 64.5
Recommend
Magazine Icon Motosports Brand Protection Magazine ZX636 03-04 Stunt Bike Build Stunt Show with Girls Baldini Stunt Show